Download Pinacle 500 Usb Software for Mac Updated FREE

Download Pinacle 500 Usb Software for Mac

In virtually cases when a USB Capture device does not work with Studio it is due to 1 of the following reasons:

  • Studio does not take the Pinnacle device selected equally the Capture Source.
  • Studio does non have the correct port selected, either Blended or South-Video.
  • The video device (camcorder, VCR, etc) is not playing video when the capture is started.

Please confirm, you accept checked those setting in Studio. If you lot have and information technology still does not work, follow the steps below. This document will assistance in installing the hardware and selecting the Pinnacle device in Studio.

This troubleshooting guide will aid you troubleshoot all Pinnacle USB capture hardware installations that are compatible with Studio. Information technology will cover the software and hardware installation of the:

Meridian

  • 700-USB
  • 500-USB
  • 710-USB
  • 510-USB

Dazzle

  • DVC 170
  • DVC 130
  • DVC 100
  • DVC 90

About of these devices install in the aforementioned way, whatsoever differences will be noted. In the images below, the Dazzle DVC 100 is used as an example of how the device is displayed in Windows and in Studio. Your hardware will be displayed with its hardware name. (Note: Some devices like the MovieBox, uses the same hardware as older packages and may evidence in the device manager with another proper name like 710 USB)

To begin, bank check to see if the device is loaded and detected by Windows by following these steps.

A. Is Studio installed?
Have you installed Studio 14/15? All the drivers for the supported hardware install automatically when you install the Studio software. If Studio is non installed, please do and then at present. Delight disconnect any Pinnacle USB capture device before y'all install Studio.

B. USB PORT:
Now that yous have Studio installed, connect the USB device upward to the proper blazon of USB port on the organization. (Notation: Some of our devices only piece of work with USB 2.0 ports and y'all need to connect these devices to a USB ii.0 port, not a USB 1 port) Windows should observe and load the drivers. If information technology does not, the Add New Hardware Wizard may ask you to scan to their location. Browse to the location on the hard drive yous installed Studio to, which is typically your C: drive. Typically, C:Programfiles\Peak/Studio14. Once Windows has found drivers for the device, check in Device Manager to run across if the driver has been loaded properly using the following steps:

  1. Click on Start - Control Panel
  2. Double-click on System
  3. Click on the Hardware tab
  4. Click on the Device Managing director push button
  5. Click on the "+" symbol (plus sign) to the left of the heading Sound, Video and Game Controllers
  6. If the device is listed properly under the Sound video and game controller section, it will await like the picture beneath. The DVC 100 is listed below as an instance. In your case, the Height device you installed must be listed similarly but with it's device name. If information technology is, movement on to Pace C, otherwise continue with Pace below.

Notation: You can also get to Device Manager by correct clicking on My Computer, then clicking on the Hardware tab and so the Device Manager button.

If the device is not listed in the Device Manager look for devices that have an "!" marked next to them, that have a proper name such as "unknown device", "other device" or devices yous know you exercise not ain, i.east. await for other devices that sound like video capture devices you exercise not own. Sometimes capture device makers will use similar hardware and windows can confuse it for another visitor'due south product and load their commuter instead of the drivers from Peak.

If y'all detect an unknown device or a device you do not recall y'all have, try un-plugging the Pinnacle USB capture device and see if the entry in question in Device Manager disappears.

If it does not, and then the unknown/other device is not the Pinnacle device simply another misconfigured commuter in your reckoner and y'all should telephone call the computer manufacturer for assistance.

If it does, then the Pinnacle drivers are non loading properly. Reconnect the hardware and remove the entry that disappears when you unhook the device and follow these steps:

If the capture device is Tiptop/Dazzle hardware such as the 500 USB or 700 USB or Dazzle DVC 100, reinstall the drivers with the following steps

  1. Shut down Studio
  2. Go to Device Manager. Start -> Control Panel -> Organization. Click on the Hardware tab, and so the Device Manager push button. Nether Sound, Video and Game controllers, find the capture device and click on information technology to highlight information technology. Click on the uninstall icon.
  3. Disconnect the 500 USB or 700 USB or Dazzle DVC 100
  4. Download driver from from Pinnacle hardware drivers download page and run the driver file that was downloaded and follow the on-screen prompts. If the hardware is installed successfully it should be listed under Sound, Video and Game controllers without any exclamation marks. If it is, then skip to Step C, otherwise your system is all the same not detecting the Pinnacle/Dazzle hardware, information technology may be lacking.

C: Capture Source Setting in Studio:
This section will show yous accept to select the device in the imported and select the input blazon the device will use.

1. Open the importer by clicking here on the import button show beneath.

2. That will bring upwardly this window.

In this window you can see what capture devices Studio detects. The Red Box shows the DVC 100 along with Video composite and Video SVideo below. The selected Capture device shows highlighted in the red box. You tin can Besides see another capture device hooked upwardly to the organisation in the Orange Box. To select this capture device y'all would merely click on it. Merely the agile capture device will have the SVideo/blended selector. You demand to make sure and select the proper input for the blazon of capture y'all are doing.

You are at present set up to apply the device to import video into Studio. For more data on how to employ the importer click here.

Download Pinacle 500 Usb Software for Mac

DOWNLOAD HERE

Source: https://kb.corel.com/en/126554

Posted by: archersaidine1942.blogspot.com

Comments

Post a Comment